android_reaver-wps

UNTESTED Reaver-WPS command-line for Android. Not proven to work with bcm4329 chipset based phones, but should probably do on bcm4330. README not meant for Android port. Binaries in /bin. Building based on Android.mk, similar to kriswebdev/android_aircrack but using "mka reaver" and "mka reaver-wash".

View the Project on GitHub aapks/android_reaver-wps

OVERVIEW

Reaver performs a brute force attack against an access point's WiFi Protected Setup pin number. 
Once the WPS pin is found, the WPA PSK can be recovered and alternately the AP's wireless settings can be 
reconfigured.

While Reaver does not support reconfiguring the AP, this can be accomplished with wpa_supplicant once 
the WPS pin is known.

DESCRIPTION

Reaver targets the external registrar functionality mandated by the WiFi Protected Setup specification.
Access points will provide authenticated registrars with their current wireless configuration (including
the WPA PSK), and also accept a new configuration from the registrar.

In order to authenticate as a registrar, the registrar must prove its knowledge of the AP's 8-digit pin
number. Registrars may authenticate themselves to an AP at any time without any user interaction. Because
the WPS protocol is conducted over EAP, the registrar need only be associated with the AP and does not 
need any prior knowledge of the wireless encryption or configuration.

Reaver performs a brute force attack against the AP, attempting every possible combination in order to
guess the AP's 8 digit pin number. Since the pin numbers are all numeric, there are 10^8 (100,000,000) 
possible values for any given pin number. However, because the last digit of the pin is a checksum value
which can be calculated based on the previous 7 digits, that key space is reduced to 10^7 (10,000,000) 
possible values.

The key space is reduced even further due to the fact that the WPS authentication protocol cuts the pin in
half and validates each half individually. That means that there are 10^4 (10,000) possible values for the
first half of the pin and 10^3 (1,000) possible values for the second half of the pin, with the last digit
of the pin being a checksum.

Reaver brute forces the first half of the pin and then the second half of the pin, meaning that the entire 
key space for the WPS pin number can be exhausted in 11,000 attempts. The speed at which Reaver can test 
pin numbers is entirely limited by the speed at which the AP can process WPS requests. Some APs are fast enough 
that one pin can be tested every second; others are slower and only allow one pin every ten seconds. Statistically, 
it will only take half of that time in order to guess the correct pin number.

WPS Connect

INSTALLATION

Reaver is only supported on the Linux platform, requires the libpcap and libsqlite3 libraries, and 
can be built and installed by running:

	$ ./configure
	$ make
	# make install

To remove everything installed/created by Reaver:

	# make distclean

KNOWN BUGS

o Some drivers don't play nice with Reaver (check the wiki for the latest list)

FILES

The following are Reaver source files:

	o 80211.c	Functions for reading, sending, and parsing 802.11 management frames
	o builder.c	Functions for building packets and packet headers
	o config.h	Generated by the configure script
	o cracker.c	Core cracking functions for Reaver.
	o defs.h	Common header with most required definitions and declarations
	o exchange.c	Functions for initiating and processing a WPS exchange
	o globule.c	Wrapper functions for accessing global settings
	o iface.c	Network interface functions
	o init.c	Initialization functions
	o keys.c	Contains tables of all possible pins
	o misc.c	Mac address conversion, debug print functions, etc
	o pins.c	Pin generation and randomization functions
	o send.c	Functions for sending WPS response messages
	o sigalrm.c	Functions for handling SIGALRM interrupts
	o sigint.c	Functions for handling SIGINT interrupts
	o wpscrack.c	Main Reaver source file
	o wps.h		Includes for wps wpa_supplicant functions
	o libwps/*	Generic library code for parsing WPS information elements

The following files have been taken from wpa_supplicant. Some have been modified from their original sources:

	o common/*
	o crypto/*
	o tls/*
	o utils/*
	o wps/*

The lwe directory contains Wireless Tools version 29, used for interfacing with Linux Wireless Extensions.